Immediately after MagicstompÅfs power is turned on, the display will momentarily read : MAGICSTOMP    V1.01 The part shown as "V1.01" above will be the version number of your firmware. The length of sound pause time has been shortened, for when switching patches that contain the following 10 effect types : [Distortion] [Amp Simulator] [Amp Multi(Chorus)] [Amp Multi(Flanger)] [Amp Multi(Tremolo)] [Amp Multi(Phaser)] [Distortion Multi(Chorus)] [Distortion Multi(Flanger)] [Distortion Multi(Tremolo)] [Distortion Multi(Phaser)] Defect corrections have been made in the 4 parameters (FB GAIN L,R,L->R,R->L) of the "Echo" effect. Defect corrections have been made in the parameter (Chorus Depth) of the "Acoustic Multi" effect. Defect corrections have been made in the parameter (Direct Pan) of the following effects : [8 Band Parallel Delay] [8 Band Serial Delay] [4 Band 2 Tap Mod. Delay] [2 Band 4 Tap Mod. Delay] [8 Multi Tap Mod. Delay] [2 Band Long + 4 Short Mod. Delay] [Short + Medium + Long Mod Delay] User updates should be done at the ownerÅfs own risk. We recommend owners to use the Sound Editor to backup any personally-made patch data prior to carrying out any upgrading procedures. Should any incidents occur during the updating process to cause failures in upgrading - such as power cables falling out _ Magicstomp may stop operating. In case of such situation, please go back and start over the updating procedure from the beginning. WINDOWS98,ME,2000,XP * If the Magicstomp USB driver has not yet been installed, please do so by following the instructions on the user's manual. * If the YAMAHA MidRadio has not yet been installed, please do so by downloading the software from one of the following URL addresses : http://www.playersparadise.net/download/ 1. Download the update "Ver.1.08" data and extract the file onto your computer. [ub99_v1_08.mid] 2. Without connecting the USB cable, turn ON your Magicstomp [plug in the power] while holding down the (STORE) and (-) buttons. 3. Check to see that your Magicstomp display reads, "UB99 P.LOAD V___ V_____ CNECT USB". 4. Connect Magicstomp and the PC using the USB cable. 5. Check to see that the lower line on your Magicstomp display reads, "NOW WAITING". 6. Activate YAMAHA MidRadio. 7. Go to [Options] on the menu bar, and choose the [Playback] tab. Select "YAMAHA USB OUT 0-1" under [Select MIDI device]. 8. Drag and drop the update data file (*.mid) onto the MidRadio window. 9. As the file begins to read, check to see that the lower line of the Magicstomp display changes to "NOW CLEAR". Then 20 seconds later, check to see that it shows, "RECEIVINGH'0000". 10. Approximately 15 minutes later, the lower line of the display will read, "COMPLETE". Upon seeing this, turn Magicstomp's power off. Your upgrading procedures are now complete. Macintosh * If the Magicstomp USB driver has not yet been installed, please do so by following the instructions on the user's manual. * If the YAMAHA MidRadio has not yet been installed, please do so by downloading the software from one of the following URL addresses : http://www.playersparadise.net/download/ Please use the Mac OS9 version of the MidRadio to carry out the firmware upgrade. (The upgrade cannot be done using the Mac OSX version of the MidRadio.) 1. Download the update "Ver.1.08" data and extract the file onto your computer. [ub99_v1_08.mid] 2. Without connecting the USB cable, turn on the power of your Magicstomp by pressing the [STORE] and [-] buttons simultaneously. 3. Check to see that your Magicstomp display reads, "UB99 P.LOAD V___ V_____ CNECT USB". 4. Connect Magicstomp and the PC using the USB cable. 5. Check to see that the lower line on your Magicstomp display reads, "NOW WAITING". 6. Activate YAMAHA MidRadio. 7. Go to [Preferences] on the [Options] menu, and choose [Playback]. Choose the YAMAHA port by ticking "Select OMS port". 8. Drag and drop the update data file (*.mid) onto the MidRadio window. 9. As the file begins to read, check to see that the lower line of the Magicstomp display changes to "NOW CLEAR". Then 20 seconds later, check to see that it shows, "RECEIVINGH'0000". 10. Approximately 15 minutes later, the lower line of the display will read, "COMPLETE". Upon seeing this, turn Magicstomp's power off. Your upgrading procedures have been completed.